2023 Current NACE-CIP1-001 dumps Preparation through Our Practice Test
100% Reliable Microsoft NACE-CIP1-001 Exam Dumps Test Pdf Exam Material
The preparation of the NACE CIP1-001 exam can be done with the best solution
You should be ready to face the tough competition of the NACE CIP1-001 exam. We provide the best solution for the preparation of the NACE CIP1-001 exam. You can easily download the NACE CIP1-001 Dumps. The practice test helps you to easily understand the pattern of the exam. It also helps the candidates to know the difficulty level of the topics covered in the NACE CIP1-001 exam. We provide the latest version of the NACE CIP1-001 practice test. The updated version of the NACE CIP1-001 practice test helps the candidates to easily pass the NACE CIP1-001 test. Update questions help you to easily prepare for the NACE CIP1-001 exam. You can easily prepare for the NACE CIP1-001 test by using the NACE CIP1-001 study material.
NEW QUESTION # 58
Check abrasive blast pressure close to the
- A. compressor
- B. substrate
- C. blast nozzle
- D. blast pot
Answer: C
NEW QUESTION # 59
Surface profile describes:
- A. The level of surface cleanliness required after abrasive blasting
- B. The general condition of the surface required after abrasive blasting
- C. The level of surface roughness required after abrasive blasting
- D. The initial condition of the surface prior to abrasive blasting
Answer: C
NEW QUESTION # 60
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. On every job
- D. When specifically identified in the owner's specification
Answer: D
NEW QUESTION # 61
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
Answer: A
NEW QUESTION # 62
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Always handwritten
- C. Submitted before the end of the job
- D. Timely, accurate and concise
Answer: D
NEW QUESTION # 63
Digital hygrometers
- A. determine relative humidity, air temperature, and dew point temperature:
- B. consist of a bimetallic sensing element protected from wind gusts.
- C. are used to measure temperature from a distance.
- D. use a thermocouple in contact with the surface to measure temperature
Answer: A
NEW QUESTION # 64
The initial steel condition is important to the NACE Inspector because:
- A. The Inspector may have to reject the Steel
- B. It affects the final appearance after blasting
- C. If the steel is pitted more coating will be required
- D. Less abrasive is need if the mill Scale s gone
Answer: A
NEW QUESTION # 65
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Never change his/her mind
- C. Achieve consensus through negotiation
- D. Call the supervisor
Answer: D
NEW QUESTION # 66
Polymerization is the process of:
- A. All thermoplastic coatings
- B. All organic coatings
- C. Monomers joining together
- D. Monomers telegraphing
Answer: C
NEW QUESTION # 67
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Act in accordance with the site safety requirements and set an example
- B. Assume the role of the Safety Inspector
- C. Check the PPE used by the Applicators
- D. Check the credentials of the Safety Officer on site
Answer: A
NEW QUESTION # 68
An inspectors personal log book should contain:
- A. The inspector's personal opinions of the application team
- B. No comments regarding the application team
- C. Subjective comments re ding the application team
- D. Objective comments regarding the application work
Answer: B
NEW QUESTION # 69
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Synthetic oil or grease may not be identified
- B. Ultra-Violet light may contaminant the surface
- C. Presence of weld spatter may produce a false positive
- D. Chloride salt may produce a false positive
Answer: A
NEW QUESTION # 70
Silicone coatings are typically:
- A. Applied in very' thin films
- B. Used as a sacrificial primer
- C. Used strictly in immersion service
- D. Applied in very thick films
Answer: A
NEW QUESTION # 71
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. inhibitor residues
- B. sulfates
- C. grease and oil
- D. soluble chemical salts
Answer: C
NEW QUESTION # 72
Removal of surface contaminants is done by:
- A. A combination of methods
- B. Scarifying
- C. Waterjetting
- D. Abrasive blasting
Answer: A
NEW QUESTION # 73
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. monitoring
- B. telegraphing.
- C. juxtaposing.
- D. transitioning.
Answer: B
NEW QUESTION # 74
The Inspector's Log Book is generally:
- A. Shared with all parties upon project completion
- B. Shredded by the inspector upon project completion
- C. Retained by the inspector upon project completion
- D. Submitted to the client upon project completion
Answer: C
NEW QUESTION # 75
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- B. Bring the matter up at the pre-job conference
- C. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- D. Default to the owner's Inspection and Test Plan
Answer: B
NEW QUESTION # 76
Prior to using Inspection Tools the inspector must:
- A. Be trained on how to use the instrument
- B. Read the manufactures' instructions
- C. Ensure the instrument is within calibration parameters
- D. a), b) & c)
Answer: D
NEW QUESTION # 77
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. blotter test for the presence of oil and water.
- B. vial lest.
- C. dry film thickness (DEI) measurement.
- D. wet film thickness (WFT) measurement.
Answer: A
NEW QUESTION # 78
......
Free NACE-CIP1-001 Dumps are Available for Instant Access: https://www.dumpexams.com/NACE-CIP1-001-real-answers.html
Based on Official Syllabus Topics of Actual NACE NACE-CIP1-001 Exam: https://drive.google.com/open?id=1j8gVknbWbh2Znhv9vTY5MWP_B2nnrDIh