2021 Latest 100% Exam Passing Ratio - NS0-183 Dumps PDF
Pass Exam With Full Sureness - NS0-183 Dumps with 145 Questions
Network Appliance NS0-183 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
| Topic 8 |
|
NetApp NS0-183 Exam Certification Details:
| Exam Registration | PEARSON VUE |
| Number of Questions | 60 |
| Passing Score | 67% |
| Exam Name | Storage Installation Engineer ONTAP |
| Exam Price | $150 USD |
| Exam Code | NS0-183 NCSIE |
| Duration | 90 minutes |
| Recommended Training | ONTAP Clustered Installation Workshop (ILT) ONTAP Cluster Administration (vILT/ILT) Universal FAS Installation (WBT) Introduction to NetApp Installation Standard (WBT) |
| Sample Questions | NetApp NS0-183 Sample Questions |
NEW QUESTION 31
You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.
Which two actions should you perform before you turn over the cluster for production? (Choose two.)
- A. Review AutoSupport messages which could explain the controller state.
- B. Execute Config Advisor again to check for new errors.
- C. Let the customer know the cluster is operating normally while the amber LED is on.
- D. Remove cables connected to the controller until you find the one responsible for the controller issue.
Answer: A,B
NEW QUESTION 32
One of the nodes in your ONTAP 9.7 cluster has failed and is not coming back online.
Which two methods would you use to connect to the node failing to come back online? (Choose two.)
- A. Use Telnet.
- B. Use the Service Processor Interface.
- C. Use Secure Shell.
- D. Use the Intelligent Platform Management Interface.
Answer: B,C
NEW QUESTION 33
While installing new Cisco cluster switches, you need to download the appropriate RCF to the switch.
In this scenario, which two file transfer protocols would be used? (Choose two.)
- A. NFS
- B. FTP
- C. SCP
- D. HTTP
Answer: B,D
NEW QUESTION 34
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)
- A. You can change any drives or disk shelves as part of this replacement procedure.
- B. You must move the boot device from the impaired node to the replacement node.
- C. The boot device must remain intact and must not be removed from the impaired node.
- D. A controller model of the same type must be used to replace the impaired node.
Answer: B,D
NEW QUESTION 35
You have just completed the installation of a FAS9000 HA pair with ONTAP 9.5.
In this scenario, according to NetApp best practices, which two tests verify the HA failover functionality? (Choose two.)
- A. Pull the motherboard out of the slot.
- B. Power cycle the node.
- C. Disconnect the HA interconnect cabling.
- D. Invoke a system core.
Answer: B,D
NEW QUESTION 36
While preparing for a new cluster installation, your customer indicates that they have some disk shelves and switches that were discontinued at their old site. They want to re-use as much of this equipment as possible. You must verify that their discontinued equipment is compatible with the new equipment they have on order.
Which two actions will accomplish this task? (Choose two.)
- A. Use the Hardware Universe portal (HWU).
- B. Verify compatibility from Activity IQ.
- C. Run the Cluster Configuration Builder tool (ConfigBuilder).
- D. look up the compatibility in the Interoperability Matrix Tool (IMT).
Answer: A,D
NEW QUESTION 37
Which two configurations use root-data-data partitioning? (Choose two.)
- A. AFF A220 with 3.8 TB internal SSD drives
- B. AFF A800 with 3.8 TB internal NVMe SSD drives
- C. FAS8080 with 1.8 TB external SAS drives
- D. FAS2650 with 1.8 TB internal SAS drives
Answer: A,B
NEW QUESTION 38
An administrator is installing a new AFF A220 HA pair and needs to convert two unified target adapter (UTA) ports from converged network adapter (CNA) to FC.
In this scenario, which action sequence will accomplish this task?
- A. 1. Set the adapter to status-admin down. 2. Set the port mode to fc. 3. Set the adapter to status-admin up. 4. Reboot the node.
- B. 1. Set the port mode to fc. 2. Set the adapter to status-admin down. 3. Reboot the node. 4. Set the adapter to status-admin up.
- C. 1. Set the adapter to status-admin down. 2. Reboot the node. 3. Set the port mode to fc. 4. Set the adapter to status-admin up.
- D. 1. Set the adapter to status-admin down. 2. Set the port mode to fc. 3. Reboot the node. 4. Set the adapter to status-admin up.
Answer: D
NEW QUESTION 39
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)
- A. You can change any drives or disk shelves as part of this replacement procedure.
- B. You must move the boot device from the impaired node to the replacement node.
- C. The boot device must remain intact and must not be removed from the impaired node.
- D. A controller model of the same type must be used to replace the impaired node.
Answer: B,D
Explanation:
Explanation/Reference: https://library.netapp.com/ecm/ecm_download_file/ECMP1147156 (2)
NEW QUESTION 40
You are installing a pair of Cisco Nexus 3132Q-V cluster switches and receive several syntax errors when the reference configuration file (RCF) is applied.
In this scenario, what are two reasons for these errors? (Choose two.)
- A. The RCF was already applied.
- B. Cables were not removed before applying the RCF.
- C. The switch was not in maintenance mode.
- D. An RCF file for a different version has been loaded.
Answer: A,D
NEW QUESTION 41
You just installed a new AFF A220 2-node cluster without additional disk shelves. When you review the Config Advisor output, you notice that your SAS cabling appears to be single-path HA.
In this scenario, which statement is true?
- A. The Config Advisor version you are using requires a plugin for AFF controllers.
- B. Cable controller 1 0a to controller 2 0a, and cable controller 1 0b to controller 2 0b.
- C. Cable controller 1 0a to controller 2 0b, and cable controller 1 0b to controller 2 0a.
- D. AFF A220 controllers with internal disks support only single-path HA.
Answer: C
NEW QUESTION 42
You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager. In this scenario, what caused this problem?
- A. You are missing a license to enable those ports.
- B. This is a hardware error and you must open a case with NetApp Support.
- C. You must first enable the ports using the network port modifycommand.
- D. Breakout cables were used and the second port on the same ASIC became disabled.
Answer: C
NEW QUESTION 43
You are creating an aggregate on a new FAS8200 with two DS224C shelves. Your customer wants to be able to use the Disk Maintenance Center.
In this scenario, what is the minimum number of spare disks required per node and disk type?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 44
A customer wants to expand their 10-node AFF A700s SAN cluster on Cisco Nexus 3132Q-V interconnect switches. The customer has six AFF A700s nodes available.
In this scenario, what should you do to expand the cluster?
- A. Replace the switches with Cisco Nexus 5596T switches and then add the six nodes.
- B. Add six nodes to the existing cluster.
- C. Add an expansion module to each switch and then add the six nodes.
- D. Add two nodes to the existing cluster without exceeding the SAN cluster limit.
Answer: D
NEW QUESTION 45
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.
Referring to the exhibit, which steps are required to get an HA cabled system?
- A. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- B. 1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- C. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.
- D. 1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
Answer: D
NEW QUESTION 46
You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.
Which tool would be used to accomplish these tasks?
- A. Active IQ Config Advisor
- B. Active IQ Unified Manager
- C. System Diagnostics
- D. Cloud Insights
Answer: C
NEW QUESTION 47
After an initial setup, you want to create a new data aggregate. The node has thirty-one 4 TB SATA spare disks assigned. Your customer wants to have two spare disks.
In this scenario, which two settings would you use to reach the maximum capacity and availability? (Choose two.)
- A. -maxraidsize 31
- B. -raidtype raid_tec
- C. -raidtype raid_dp
- D. -maxraidsize 29
Answer: B,D
NEW QUESTION 48
What is the maximum port speed of an Ethernet port on a Cisco Nexus 3232C cluster-interconnect switch?
- A. 200GbE
- B. 40GbE
- C. 100GbE
- D. 10GbE
Answer: B
NEW QUESTION 49
When completing a new ONTAP 9.5 cluster base installation, which three SVM types will be present on the system by default? (Choose three.)
- A. system SVM
- B. data SVM
- C. cluster SVM
- D. node SVM
- E. admin SVM
Answer: A,D,E
NEW QUESTION 50
You are creating a new aggregate with one RAID-TEC RAID group.
How many parity drives are used in this scenario?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 51
A customer wants to reduce the task allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The small part is used for the root aggregate and the large part for the data aggregates?
In this situation, what is this feature called?
- A. storage virtual machine
- B. RAID
- C. Advanced Drive Partitioning
- D. ONTAP
Answer: C
NEW QUESTION 52
......
Verified NS0-183 dumps Q&As - 100% Pass from Dumpexams: https://www.dumpexams.com/NS0-183-real-answers.html